Exam # 308 Servers - PowerEdge 1650 Product

PowerEdge 1650使用手册下载

The PowerEdge 1650 must be removed from the rack before removing the front bezel.
===False.
True.

Where is the top system panel lock release located on the PowerEdge 1650?
Next to the back USB connections.
---Next to the front USB connection.
Next to the back PCI slots.
Next to the CD-ROM.

Where is the metal tab located that is used to remove the CD-ROM on the PowerEdge 1650?
Under the control panel fan.
Next to the system fan.
===Next to the IDE CD-ROM cable.
Next to the system memory.

Choose all that apply:
What must be done before removing the floppy-diskette drive cable on the PowerEdge 1650?
===Open the top panels.
===Remove the front bezel.
===Pull the ZIF connector up.
Press the metal tab next to the front power supply.

To replace the back power supply on the PowerEdge 1650, slide the back power supply towards the front of the system.
===False.
True.

What must be done before removing the back power supply fan on the PowerEdge 1650?
Remove the front power supply.
---Disconnect the back power supply fan cable.
Remove the back power supply.
Remove the PSDB.

On the PowerEdge 1650, where is the fan bracket release located?
Next to the control panel.
Next to the CD-ROM drive.
===Next to the front power supply.
Next to the PCI riser board.

Where is the SCSI backplane board handle located on the PowerEdge 1650?
---Behind the floppy-diskette drive next to the SCSI backplane release latch.
Between the SCSI backplane and the VRM's.
Between the SCSI backplane and the CD-ROM drive.
A SCSI backplane release tab does not exist.

You must loosen the PCI expansion card latch in order to replace a PCI expansion card on the PowerEdge 1650.
False.
---True.

Choose all that apply:
What must be done before replacing the PCI expansion riser board on the PowerEdge 1650?
===Remove the front bezel.
Remove the system fans.
===Remove any PCI expansion cards.
===Open the top panel.

What cable connection should be verified when replacing the ROMB mezzanine board on the PowerEdge 1650?
===The battery cable.
The riser cable.
The ROMB cache connection cable.
The SCSI cable.

On the PowerEdge 1650, what secures the system board to the chassis?
Retaining clips.
A metal clamp.
===A thumbscrew.
A solder joint.

On the PowerEdge 1650, the cable connecting the control panel to the system board is routed between what two components?
===The front power supply and hard-disk drive 0.
The front power supply and the ERA.
The front and back power supplies.
The floppy-diskette drive and the CD-ROM drive.

On the PowerEdge 1650, you must press out on the memory module ejector on each end of the socket to remove a memory module.
---True.
False.

Choose all that apply:
What must be done before replacing the embedded remote administrator card on the PowerEdge 1650?
---Open the top panels.
---Remove the front bezel.
Disconnect the ERA network cable.
Disconnect the ERA cable.

On the PowerEdge 1650, what must be removed before removing the PSDB?
System memory.
SCSI backplane.
===PSDB shield.
VRM's.

Where is the PSDB located on the PowerEdge 1650?
Between the floppy-diskette drive and CD-ROM drive.
===Power supply bay area.
Built into the SCSI backplane.
Next to the PCI expansion riser board.

To replace a processor on the PowerEdge 1650, which of the following components must be removed?
System memory.
===Processor heat sink.
PSDB.
VRM.

On the PowerEdge 1650, a terminator card is required if there is only one processor in installed in the system.
True.
===False.

A PowerEdge 1650 configured with IDE hard-disk drives will not contain a hard-disk drive backplane.
---True.
False.

On a PowerEdge 1650, hard-disk drives are hot swappable when connected to the onboard Adaptec 7899 non-RAID controller?
---False.
True.

What channel are the IDE hard-disk drives connected to on the PowerEdge 1650?
Primary SCSI channel.
Secondary SCSI channel.
Secondary IDE channel.
---Primary IDE channel.

What must be performed before removing a SCSI hard-disk drive from a PowerEdge 1650?
Remove the top system panels.
===Remove the front bezel.
Remove the drive-retention bracket.
Remove the serial cable.

Which Adaptec SCSI controller is integrated into the systemboard on a PowerEdge 1650?
===AIC-7899W.
AIC-7890.
AIC-7860.
AIC-7799.

What is the maximum amount of system memory a PowerEdge 1650 can support?
2 GB.
===4 GB.
512 MB.
256 MB.

What RAID option is available for the internal SCSI drives on a PowerEdge 1650?
PERC 3/DC.
PERC 3/SI.
PERC 3/DCL.
===PERC 3/DI.

The PowerEdge 1650 has ________ embedded Intel Pro 1000 XT Gigabit NICs.
===Two.
One.
Three.
Zero.

The riser board on a PowerEdge 1650 supports three 32-bit/33 MHz PCI cards.
True.
---False.

The CD-ROM device on a PowerEdge 1650 is connected to the secondary channel when IDE hard-disk drives are installed.
True.
---False.

How many processors will a PowerEdge 1650 support?
Four.
One.
Three.
===Two.